| Norm / STD | Description |
|---|---|
| AAMA 101 | Standard/specification for windows, doors, and skylights |
| AAMA 1304 | Voluntary specification for forced entry resistance of side-hinged door systems |
| AAMA 1503 | Voluntary test method for thermal transmittance and condensation resistance of windows, doors and glazed wall sections |
| AAMA 1801 | Voluntary specification for the acoustical rating of exterior windows, doors, skylights and glazed wall sections |
| AAMA 501.1 | Standard Test Method for Water Penetration of Windows, Curtain Walls and Doors Using Dynamic Pressure |
| AAMA 501.4 | Recommended Static Testing Method for Evaluating Curtain Wall and Storefront Systems Subjected to Seismic and Wind Induced Interstory Drift |
| AAMA 501.5 | Test Method for Thermal Cycling Of Exterior Walls |
| AAMA 501.6 | Recommended dynamic test method for determining the seismic drift causing glass fallout from a wall system |
| AAMA 501.7 | Recommended Static Test Method for Evaluating Windows, Window Wall, Curtain Wall and Storefront Systems Subjected to Vertical Inter-Story Movements |
| AAMA 507 | Standard practice for determining the thermal performance characteristics of fenestration systems installed in commercial buildings |
| AAMA 510 | Voluntary guide specification for blast hazard mitigation for vertical fenestration systems |
| AAMA 711 | Specification for self-adhering flashing for exterior wall fenestration installation |
| AAMA 712 | Voluntary specification for mechanically attached flexible flashing |
| AAMA 920 | Specification for operating cycle performance of active side-hinged exterior door slabs |
| AAMA 925 | Specification for determining the vertical loading resistance of side-hinged door leaves |
| AATCC 127 | Water resistance - hydrostatic pressure test |
| ABNT NBR 10821-3 | Exterior door and window frames for buildings Part 3: Test methods |
| AISI S904 | Standard Test Method for determining the Tensile and Shear strengths of Screws |
| AISI S905 | Test methods for mechanically fastened cold-formed steel connections |
| ANSI Z26.1 | Standard for safety glazing materials for glazing motor vehicles and motor vehicle equipment operating on land highways - safety code |
| ANSI Z97.1 | Standard for safety glazing materials used in buildings - safety performance specifications and methods of test |
| ANSI/ASA S12.51 | Acoustics – determination of sound power levels and sound energy levels of noise sources using sound pressure – precision methods for reverberation test rooms |
| ANSI/ASSE Z359.18 | Safety Requirements for Anchorage Connectors for Active Fall Protection Systems |
| ANSI/BHMA A156.1 | Butts and hinges |
| ANSI/BHMA A156.11 | Cabinet locks |
| ANSI/BHMA A156.12 | Interconnected locks & latches |
| ANSI/BHMA A156.13 | Mortise locks |
| ANSI/BHMA A156.14 | Sliding and folding hardware |
| ANSI/BHMA A156.15 | Release devices |
| ANSI/BHMA A156.16 | Auxiliary hardware |
| ANSI/BHMA A156.17 | Self closing hinges |
| ANSI/BHMA A156.18 | Materials and finishes |
| ANSI/BHMA A156.19 | Power assist & low energy power operated doors |
| ANSI/BHMA A156.2 | Bored & preassembled locks and latches |
| ANSI/BHMA A156.20 | Strap and tee hinges, and hasps |
| ANSI/BHMA A156.21 | Thresholds |
| ANSI/BHMA A156.23 | Electromagnetic locks |
| ANSI/BHMA A156.24 | Delayed egress locks |
| ANSI/BHMA A156.26 | Continuous hinges |
| ANSI/BHMA A156.3 | Exit devices |
| ANSI/BHMA A156.31 | Electric strikes and frame mounted actuators |
| ANSI/BHMA A156.32 | Integrated door opening assemblies |
| ANSI/BHMA A156.36 | Auxiliary locks |
| ANSI/BHMA A156.4 | Door controls-closers |
| ANSI/BHMA A156.5 | Cylinders and input devices for locks |
| ANSI/BHMA A156.6 | Architectural door trim |
| ANSI/BHMA A156.8 | Overhead stops & holders |
| ANSI/BHMA A156.9 | Cabinet hardware |
| ANSI/DASMA 108 | Standard method for testing sectional garage doors and rolling doors – determination of structural performance under uniform static air pressure difference |
| ANSI/DASMA 115 | Standard method for testing sectional garage doors and rolling doors – determination of structural performance under missile impact and cyclic wind pressure |
| ANSI/SPRI ES-1 | Wind design standard for edge systems used with low slope roof systems (limited to SPRI test RE-1, RE-2 and RE-3) |
| ANSI/SPRI GD-1 | Structural design standard for gutter systems used with low-slope roofs |
| ANSI/TPI 1 | National design standard for metal plate connected wood truss construction |
| ANSI/WMA 100 | Standard Method of Determining Structural Performance Ratings of Side-Hinged Exterior Door Systems and Procedures for Component Substitution |
| AS 4586 | Slip Resistance Classification of New Pedestrian Surface Materials. |
| ASTM A370 | Standard test methods and definitions for mechanical testing of steel products |
| ASTM A90/A90M | Standard test method for weight [mass] of coating on iron and steel articles with zinc or zinc-alloy coatings |
| ASTM B117 | Standard practice for operating salt spray (fog) apparatus |
| ASTM B499 | Standard test method for measurement of coating thicknesses by the magnetic method: nonmagnetic coatings on magnetic basis metals |
| ASTM C1019 | Standard test method for sampling and testing grout |
| ASTM C1021 | Standard practice for laboratories engaged in testing of building sealants (for performance of ASTM C661 and ASTM C719) |
| ASTM C109/C109M | Standard test method for compressive strength of hydraulic cement mortars (using 2-in. or [50-mm] cube specimens) |
| ASTM C1166 | Standard test method for flame propagation of dense and cellular elastomeric gaskets and accessories |
| ASTM C1185 | Standard test methods for sampling and testing non-asbestos fiber-cement flat sheet, roofing and siding shingles, and clapboards |
| ASTM C1186 | Standard specification for flat fiber-cement sheets |
| ASTM C1199 | Standard test method for measuring the steady-state thermal transmittance of fenestration systems using hot box methods |
| ASTM C1279 | Standard test method for non-destructive photo-elastic measurement of edge and surface stresses in annealed, heat-strengthened, and fully tempered flat glass |
| ASTM C1289 | Standard specification for faced rigid cellular polyisocyanurate thermal insulation board |
| ASTM C1305 | Standard test method for crack bridging ability of liquid-applied waterproofing membrane |
| ASTM C1314 | Standard test method for compressive strength of masonry prisms |
| ASTM C1353/C1353M | Standard test method for abrasion resistance of dimension stone subjected to foot traffic using a rotary platform abraser |
| ASTM C1354/C1354M | Standard test method for strength of individual stone anchorages in dimension stone |
| ASTM C1363 | Standard test method for thermal performance of building materials and envelope assemblies by means of a hot box apparatus |
| ASTM C140/C140M | Standard test methods for sampling and testing concrete masonry units and related units |
| ASTM C1401 | Standard guide for structural sealant glazing |
| ASTM C1521 | Standard practice for evaluating adhesion of installed weatherproofing sealant joints |
| ASTM C1522 | Standard test method for extensibility after heat aging of cold liquid-applied elastomeric waterproofing membranes |
| ASTM C1523 | Standard test method for determining modulus, tear and adhesion properties of precured elastomeric joint sealants |
| ASTM C1609/C1609M | Standard test method for flexural performance of fiber-reinforced concrete (using beam with third-point loading) |
| ASTM C1651 | Standard test method for measurement of roll wave optical distortion in heat-treated flat glass |
| ASTM C1652/C1652M | Standard test method for measuring optical distortion in flat glass products using digital photography of grids |
| ASTM C170/C170M | Standard test method for compressive strength of dimension stone |
| ASTM C203 | Standard test methods for breaking load and flexural properties of block-type thermal insulation |
| ASTM C209 | Standard test methods for cellulosic fiber insulating board |
| ASTM C236 | Standard test method for steady-state thermal performance of building assemblies by means of a guarded hot box |
| ASTM C271/C271M | Standard test method for density of sandwich core materials |
| ASTM C273/C273M | Standard test method for shear properties of sandwich core materials |
| ASTM C297/C297M | Standard test method for flatwise tensile strength of sandwich constructions |
| ASTM C303 | Standard test method for dimensions and density of preformed block and board–type thermal insulation |
| ASTM C348 | Standard test method for flexural strength of hydraulic-cement mortars |
| ASTM C393/C393M | Standard test method for core shear properties of sandwich constructions by beam flexure |
| ASTM C411 | Standard Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation |
| ASTM C423 | Standard test method for sound absorption and sound absorption coefficients by the reverberation room method |
| ASTM C469/C469M | Standard test method for static modulus of elasticity and Poisson’s ratio of concrete in compression |
| ASTM C472 | Standard Test Methods for Physical Testing of Gypsum, Gypsum Plasters and Gypsum Concrete |
| ASTM C473 | Standard test methods for physical testing of gypsum panel products |
| ASTM C474 | Standard Test Methods for Joint Treatment Materials for Gypsum Board Construction |
| ASTM C484 | Standard test method for thermal shock resistance of glazed ceramic tile |
| ASTM C495/C495M | Standard test method for compressive strength of lightweight insulating concrete |
| ASTM C496/C496M | Standard test method for splitting tensile strength of cylindrical concrete specimens |
| ASTM C511 | Standard specification for mixing rooms, moist cabinets, moist rooms, and water storage tanks used in the testing of hydraulic cements and concretes |
| ASTM C518 | Standard test method for steady-state thermal transmission properties by means of the heat flow meter apparatus |
| ASTM C522 | Standard test method for airflow resistance of acoustical materials |
| ASTM C550 | Standard test method for measuring trueness and squareness of rigid block and board thermal insulation |
| ASTM C567/C567M | Standard test method for determining density of structural lightweight concrete |
| ASTM C612 | Standard specification for mineral fiber block and board thermal insulation |
| ASTM C635 | Standard specification for the manufacture, performance, and testing of metal suspension systems for acoustical tile and lay-in panel ceilings |
| ASTM C645 | Standard specification for nonstructural steel framing members |
| ASTM C661 | Standard test method for indentation hardness of elastomeric-type sealants by means of a durometer |
| ASTM C666/C666M | Standard test method for resistance of concrete to rapid freezing and thawing |
| ASTM C672/C672M | Standard test method for scaling resistance of concrete surfaces exposed to deicing chemicals |
| ASTM C719 | Standard test method for adhesion and cohesion of elastomeric joint sealants under cyclic movement (Hockman cycle) |
| ASTM C864 | Standard specification for dense elastomeric compression seal gaskets, setting blocks, and spacers |
| ASTM C880/C880M | Standard test method for flexural strength of dimension stone |
| ASTM C90 | Standard specification for loadbearing concrete masonry units |
| ASTM C97/C97M | Standard test methods for absorption and bulk specific gravity of dimension stone |
| ASTM C99/C99M | Standard test method for modulus of rupture of dimension stone |
| ASTM D1002 | Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal) |
| ASTM D1003 | Standard test method for haze and luminous transmittance of transparent plastics |
| ASTM D1004 | Standard test method for tear resistance (graves tear) of plastic film and sheeting |
| ASTM D1005 | Standard test method for measurement of dry-film thickness of organic coatings using micrometers |
| ASTM D1037 | Standard test methods for evaluating properties of wood-base fiber and particle panel materials |
| ASTM D1042 | Standard test method for linear dimensional changes of plastics caused by exposure to heat and moisture |
| ASTM D1149 | Standard test methods for rubber deterioration—cracking in an ozone controlled environment |
| ASTM D1183 | Standard Practices for Resistance of Adhesives to Cyclic Laboratory Aging Conditions |
| ASTM D1204 | Standard test method for linear dimensional changes of non-rigid thermoplastic sheeting or film at elevated temperature |
| ASTM D1212 | Standard Test Methods for Measurement of Wet Film Thickness of Organic Coatings |
| ASTM D1400 | Standard test method for nondestructive measurement of dry film thickness of nonconductive coatings applied to a nonferrous metal base |
| ASTM D143 | Standard test methods for small clear specimens of timber |
| ASTM D1435 | Standard practice for outdoor weathering of plastics |
| ASTM D1621 | Standard test method for compressive properties of rigid cellular plastics |
| ASTM D1622/D1622M | Standard test method for apparent density of rigid cellular plastics |
| ASTM D1623 | Standard test method for tensile and tensile adhesion properties of rigid cellular plastics |
| ASTM D1644 | Standard test methods for nonvolatile content of varnishes |
| ASTM D1653 | Standard test methods for water vapor transmission of organic coating films |
| ASTM D1761 | Standard test methods for mechanical fasteners in wood |
| ASTM D1781 | Standard test method for climbing drum peel for adhesives |
| ASTM D1876 | Standard Test Method for Peel Resistance of Adhesives (T-Peel Test) |
| ASTM D1894 | Standard test method for static and kinetic coefficients of friction of plastic film and sheeting |
| ASTM D1929 | Standard test method for determining ignition temperature of plastics |
| ASTM D1970/D1970M | Standard specification for self-adhering polymer modified bituminous sheet materials used as steep roofing underlayment for ice dam protection |
| ASTM D198 | Standard test methods of static tests of lumber in structural sizes |
| ASTM D2017 | Standard test method of accelerated laboratory test of natural decay resistance of woods |
| ASTM D2126 | Standard test method for response of rigid cellular plastics to thermal and humid aging |
| ASTM D2136 | Standard test method for coated fabrics—low-temperature bend test |
| ASTM D2137 | Standard test methods for rubber property - brittleness point of flexible polymers and coated fabrics |
| ASTM D2196 | Standard test methods for rheological properties of non-Newtonian materials by rotational viscometer |
| ASTM D2240 | Standard test method for rubber property—durometer hardness |
| ASTM D2244 | Standard practice for calculation of color tolerances and color differences from instrumentally measured color coordinates |
| ASTM D2247 | Standard practice for testing water resistance of coatings in 100% relative humidity |
| ASTM D2294 | Standard Test Method for Creep Properties of Adhesives in Shear by Tension Loading (Metal-to-Metal) |
| ASTM D2370 | Standard test method for tensile properties of organic coatings |
| ASTM D2394 | Standard test methods for simulated service testing of wood and wood-base finish flooring |
| ASTM D2395 | Standard test methods for density and specific gravity (relative density) of wood and wood-based materials |
| ASTM D256 | Standard test methods for determining the Izod pendulum impact resistance of plastics |
| ASTM D2565 | Standard practice for xenon-arc exposure of plastics intended for outdoor applications |
| ASTM D2583 | Standard test method for indentation hardness of rigid plastics by means of a Barcol impressor |
| ASTM D2842 | Standard test method for water absorption of rigid cellular plastics |
| ASTM D2843 | Standard test method for density of smoke from the burning or decomposition of plastics |
| ASTM D2939 | Standard Test Methods for Emulsified Bitumens Used as Protective Coatings |
| ASTM D2990 | Standard test methods for tensile, compressive, and flexural creep and creep-rupture of plastics |
| ASTM D3043 | Standard Test Methods for Structural Panels in Flexure |
| ASTM D3045 | Standard practice for heat aging of plastics without load |
| ASTM D3161/D3161M | Standard test method for wind-resistance of steep slope roofing products (fan-induced method) |
| ASTM D3201 | Standard Test Method for Hygroscopic Properties of Fire-Retardant Wood and Wood-Based Products |
| ASTM D3500 | Standard Test Methods for Structural Panels in Tension |
| ASTM D3679 | Standard specification for rigid poly (vinyl chloride) (PVC) siding |
| ASTM D3801 | Standard test method for measuring the comparative burning characteristics of solid plastics in a vertical position |
| ASTM D395 | Standard test methods for rubber property—compression set |
| ASTM D4060 | Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
| ASTM D4073 | Standard Test Method for Tensile-Tear Strength of Bituminous Roofing Membranes |
| ASTM D412 | Standard test methods for vulcanized rubber and thermoplastic elastomers—tension |
| ASTM D4226 | Standard test methods for impact resistance of rigid poly (vinyl chloride) (PVC) building products |
| ASTM D4329 | Standard practice for fluorescent ultraviolet (UV) lamp apparatus exposure of plastics |
| ASTM D4385 | Standard Practice for Classifying Visual Defects in Thermosetting Reinforced Plastic Pultruded Products |
| ASTM D4434/D4434M | Standard specification for poly (vinyl chloride) sheet roofing |
| ASTM D4442 | Standard test methods for direct moisture content measurement of wood and wood-based materials |
| ASTM D4444 | Standard test method for laboratory standardization and calibration of hand-held moisture meters |
| ASTM D4533/D4533M | Standard test method for trapezoid tearing strength of geotextiles |
| ASTM D4541 | Standard test method for pull-off strength of coatings using portable adhesion testers |
| ASTM D471 | Standard test method for rubber property—effect of liquids |
| ASTM D4761 | Standard test methods for mechanical properties of lumber and wood-base structural material |
| ASTM D4798/4798M | Standard practice for accelerated weathering test conditions and procedures for bituminous materials (xenon-arc method) |
| ASTM D4804 | Standard test method for determining the flammability characteristics of non-rigid solid plastics |
| ASTM D5034 | Standard test method for breaking strength and elongation of textile fabrics (grab test) |
| ASTM D5035 | Standard test method for breaking force and elongation of textile fabrics (strip method) |
| ASTM D5206 | Standard test method for wind-load resistance of rigid plastic siding |
| ASTM D522/D522M | Standard test methods for mandrel bend test of attached organic coatings |
| ASTM D5240/D5240M | Standard test method for evaluation of durability of rock for erosion control using sodium sulfate or magnesium sulfate |
| ASTM D5420 | Standard test method for impact resistance of flat, rigid plastic specimen by means of a striker impacted by a falling weight (Gardner impact) |
| ASTM D5516 | Standard Test Method for Evaluating the Flexural Properties of Fire-Retardant Treated Softwood Plywood Exposed to Elevated Temperatures |
| ASTM D5602/D5602M | Standard test method for static puncture resistance of roofing membrane specimens |
| ASTM D5635/D5635M | Standard test method for dynamic puncture resistance of roofing membrane specimens |
| ASTM D5664 | Standard Test Method for Evaluating the Effects of Fire-Retardant Treatments and Elevated Temperatures on Strength Properties of Fire-Retardant Treated Lumber |
| ASTM D570 | Standard test method for water absorption of plastics |
| ASTM D573 | Standard test method for rubber—deterioration in an air oven |
| ASTM D5764 | Standard test method for evaluating dowel-bearing strength of wood and wood-based products |
| ASTM D6083 | Standard specification for liquid applied acrylic coating used in roofing |
| ASTM D610 | Standard Practice for Evaluating Degree of Rusting on Painted Steel Surfaces |
| ASTM D6109 | Standard test methods for flexural properties of unreinforced and reinforced plastic lumber and related products |
| ASTM D6110 | Standard test method for determining the Charpy impact resistance of notched specimens of plastics |
| ASTM D6117 | Standard test methods for mechanical fasteners in plastic lumber and shapes |
| ASTM D6132 | Standard test method for nondestructive measurement of dry film thickness of applied organic coatings using an ultrasonic coating thickness gage |
| ASTM D618 | Standard practice for conditioning plastics for testing |
| ASTM D624 | Standard test method for tear strength of conventional vulcanized rubber and thermoplastic elastomers |
| ASTM D6341 | Standard test method for determination of the linear coefficient of thermal expansion of plastic lumber and plastic lumber shapes between –30 and 140°F (–34.4 and 60°C) |
| ASTM D635 | Standard test method for rate of burning and/or extent and time of burning of plastics in a horizontal position |
| ASTM D638 | Standard test method for tensile properties of plastics |
| ASTM D6662 | Standard specification for polyolefin-based plastic lumber decking boards |
| ASTM D6694/D6694M | Standard specification for liquid-applied silicone coating used in spray polyurethane foam roofing systems |
| ASTM D6817/D6817M | Standard specification for rigid cellular polystyrene geofoam |
| ASTM D695 | Standard test method for compressive properties of rigid plastics |
| ASTM D696 | Standard test method for coefficient of linear thermal expansion of plastics between −30°C and 30°C with a vitreous silica dilatometer |
| ASTM D7031 | Standard guide for evaluating mechanical and physical properties of wood-plastic composite products |
| ASTM D7032 | Standard specification for establishing performance ratings for wood-plastic composite and plastic lumber deck boards, stair treads, guards, and handrails |
| ASTM D7091 | Standard practice for nondestructive measurement of dry film thickness of nonmagnetic coatings applied to ferrous metals and nonmagnetic, nonconductive coatings applied to non-ferrous metals |
| ASTM D7147 | Standard specification for testing and establishing allowable loads of joist hangers |
| ASTM D7254 | Standard specification for polypropylene (PP) siding |
| ASTM D746 | Standard test method for brittleness temperature of plastics and elastomers by impact |
| ASTM D751 | Standard test methods for coated fabrics |
| ASTM D790 | Standard test methods for flexural properties of unreinforced and reinforced plastics and electrical insulating materials |
| ASTM D792 | Standard test methods for density and specific gravity (relative density) of plastics by displacement |
| ASTM D882 | Standard test method for tensile properties of thin plastic sheeting |
| ASTM D896 | Standard Practice for Resistance of Adhesive Bonds to Chemical Reagents |
| ASTM D903 | Standard test method for peel or stripping strength of adhesive bonds |
| ASTM D905 | Standard Test Method for Strength Properties of Adhesive Bonds in Shear by Compression Loading |
| ASTM D925 | Standard test methods for rubber property—staining of surfaces (contact, migration, and diffusion) |
| ASTM D95 | Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation |
| ASTM D953 | Standard Test Method for Bearing Strength of Plastics |
| ASTM E1007 | Standard test method for field measurement of tapping machine impact sound transmission through floor-ceiling assemblies and associated support structures |
| ASTM E1050 | Standard test method for impedance and absorption of acoustical materials using a tube, two microphones and a digital frequency analysis system |
| ASTM E108 | Standard test methods for fire tests of roof coverings |
| ASTM E1105 | Standard test method for field determination of water penetration of installed exterior windows, skylights, doors, and curtain walls, by uniform or cyclic static air pressure difference |
| ASTM E1110 | Standard classification for determination of articulation class |
| ASTM E1111/E1111M | Standard test method for measuring the interzone attenuation of open office components |
| ASTM E119 | Standard test methods for fire tests of building construction and materials |
| ASTM E1222 | Standard test method for laboratory measurement of the insertion loss of pipe lagging systems |
| ASTM E1233/E1233M | Standard test method for structural performance of exterior windows, doors, skylights, and curtain walls by cyclic air pressure differential |
| ASTM E1332 | Standard classification for rating outdoor-indoor sound attenuation |
| ASTM E136 | Standard test method for behavior of materials in a vertical tube furnace at 750°C |
| ASTM E1414/E1414M | Standard test method for airborne sound attenuation between rooms sharing a common ceiling plenum |
| ASTM E1425 | Standard practice for determining the acoustical performance of windows, doors, skylight, and glazed wall systems |
| ASTM E1477 | Standard test method for luminous reflectance factor of acoustical materials by use of integrating-sphere reflectometers |
| ASTM E1592 | Standard test method for structural performance of sheet metal roof and siding systems by uniform static air pressure difference |
| ASTM E1886 | Standard test method for performance of exterior windows, curtain walls, doors, and impact protective systems impacted by missile(s) and exposed to cyclic pressure differentials |
| ASTM E1966 | Standard test method for fire-resistive joint systems |
| ASTM E1996 | Standard specification for performance of exterior windows, curtain walls, doors, and impact protective systems impacted by windborne debris in hurricanes |
| ASTM E2025 | Standard test method for evaluating fenestration components and assemblies for resistance to impact energies |
| ASTM E2067 | Standard practice for full-scale oxygen consumption calorimetry fire tests |
| ASTM E2068 | Standard test method for determination of operating force of sliding windows and doors |
| ASTM E2098/E2098M | Standard test method for determining tensile breaking strength of glass fiber reinforcing mesh for use in class PB exterior insulation and finish systems (EIFS), after exposure to a sodium hydroxide solution |
| ASTM E2126 | Standard test methods for cyclic (reversed) load test for shear resistance of vertical elements of the lateral force resisting systems for buildings |
| ASTM E2178 | Standard test method for air permeance of building materials |
| ASTM E2179 | Standard test method for laboratory measurement of the effectiveness of floor coverings in reducing impact sound transmission through concrete floors |
| ASTM E2188 | Standard test method for insulating glass unit performance |
| ASTM E2189 | Standard test method for testing resistance to fogging in insulating glass units |
| ASTM E2190 | Standard specification for insulating glass unit performance and evaluation |
| ASTM E2226 | Standard practice for application of hose stream |
| ASTM E2235 | Standard test method for determination of decay rates for use in sound insulation test methods |
| ASTM E2268 | Standard test method for water penetration of exterior windows, skylights, and doors by rapid pulsed air pressure difference |
| ASTM E2273 | Standard test method for determining the drainage efficiency of exterior insulation and finish systems (EIFS) clad wall assemblies |
| ASTM E2353 | Standard test methods for performance of glazing in permanent railing systems, guards, and balustrades |
| ASTM E2357 | Standard test method for determining air leakage of air barrier assemblies |
| ASTM E2485/E2485M | Standard test method for freeze/thaw resistance of exterior insulation and finish systems (EIFS) and water resistive barrier coatings |
| ASTM E2486/E2486M | Standard test method for impact resistance of class PB and PI exterior insulation and finish systems (EIFS) |
| ASTM E2568 | Standard specification for PB exterior insulation and finish systems |
| ASTM E2649 | Standard test method for determining argon concentration in sealed insulating glass units using spark emission spectroscopy |
| ASTM E283 | Standard test method for determining rate of air leakage through exterior windows, curtain walls, and doors under specified pressure differences across the specimen |
| ASTM E303 | Standard test method for measuring surface frictional properties using the British pendulum tester |
| ASTM E313 | Standard practice for calculating yellowness and whiteness indices from instrumentally measured color coordinates |
| ASTM E329 | Standard specification for agencies engaged in construction inspection, testing, or special inspection |
| ASTM E330/E330M | Standard test method for structural performance of exterior windows, doors, skylights and curtain walls by uniform static air pressure difference |
| ASTM E331 | Standard test method for water penetration of exterior windows, skylights, doors, and curtain walls by uniform static air pressure difference |
| ASTM E336 | Standard test method for measurement of airborne sound attenuation between rooms in buildings |
| ASTM E413 | Classification for rating sound insulation |
| ASTM E447 | Test methods for compressive strength of laboratory constructed masonry prisms |
| ASTM E455 | Standard test method for static load testing of framed floor or roof diaphragm constructions for buildings |
| ASTM E488/E488M | Standard test methods for strength of anchors in concrete elements |
| ASTM E492 | Standard test method for laboratory measurement of impact sound transmission through floor-ceiling assemblies using the tapping machine |
| ASTM E546 | Standard test method for frost/dew point of sealed insulating glass units |
| ASTM E547 | Standard test method for water penetration of exterior windows, skylights, doors, and curtain walls by cyclic static air pressure difference |
| ASTM E564 | Standard practice for static load test for shear resistance of framed walls for buildings |
| ASTM E596 | Standard test method for laboratory measurement of noise reduction of sound-isolating enclosures |
| ASTM E603 | Standard guide for room fire experiments |
| ASTM E661 | Standard test method for performance of wood and wood-based floor and roof sheathing under concentrated static and impact loads |
| ASTM E695 | Standard Test Method of Measuring Relative Resistance of Wall, Floor, and Roof Construction to Impact Loading |
| ASTM E699 | Standard specification for agencies involved in testing, quality assurance and evaluating of manufactured building components |
| ASTM E72 | Standard test methods of conducting strength tests of panels for building construction |
| ASTM E773 | Standard test method for accelerated weathering of sealed insulating glass units |
| ASTM E774 | Standard specification for the classification of the durability of sealed insulating glass units |
| ASTM E783 | Standard test method for field measurement of air leakage through installed exterior windows and doors |
| ASTM E795 | Standard practices for mounting test specimens during sound absorption tests |
| ASTM E8/E8M | Standard test methods for tension testing of metallic materials |
| ASTM E814 | Standard test method for fire tests of penetration firestop systems |
| ASTM E84 | Standard test method for surface burning characteristics of building materials |
| ASTM E90 | Standard test method for laboratory measurement of airborne sound transmission loss of building partitions and elements |
| ASTM E935 | Standard test methods for performance of permanent metal railing systems and rails for buildings |
| ASTM E96/E96M | Standard test methods for water vapor transmission of materials |
| ASTM E966 | Standard guide for field measurements of airborne sound insulation of building facades and facade elements |
| ASTM E989 | Standard classification for determination of impact insulation class (IIC) |
| ASTM F1233 | Standard test method for security glazing materials and systems |
| ASTM F1306 | Standard test method for slow rate penetration resistance of flexible barrier films and laminates |
| ASTM F1450 | Standard Test Methods for Hollow Metal Swinging Door Assemblies for Detention and Correctional Facilities |
| ASTM F1575 | Standard Test Method for Determining Bending Yield Moment of Nails |
| ASTM F1592 | Standard test methods for detention hollow metal vision systems |
| ASTM F1642 | Standard test method for glazing and glazing systems subject to air-blast loadings |
| ASTM F1915 | Standard test methods for glazing for detention facilities |
| ASTM F2090 | Standard specification for window fall prevention devices with emergency escape (egress) release mechanisms |
| ASTM F2927 | Standard test method for door systems subject to airblast loadings |
| ASTM F3038 | Standard test method for timed evaluation of forced-entry-resistant system |
| ASTM F588 | Standard test methods for measuring the forced entry resistance of window assemblies |
| ASTM F606/F606M | Standard test methods for determining the mechanical properties of externally and internally threaded fasteners, washers, direct tension indicators, and rivets |
| ASTM F842 | Standard test methods for measuring the forced entry resistance of sliding door assemblies |
| ASTM G154 | Standard practice for operating fluorescent ultraviolet (UV) lamp apparatus for exposure of nonmetallic materials |
| ASTM G155 | Standard practice for operating xenon arc light apparatus for exposure of non-metallic materials |
| AWPA E12 | Standard method of determining corrosion of metal in contact with treated wood |
| BS 6206 | Specification for impact performance requirements for flat safety glass and safety plastics for use in buildings |
| BS 7976-2+A1 | Pendulum testers. Method of operation |
| BS EN 12152 | Curtain walling. Air permeability. Performance requirements and classification |
| BS EN 12153 | Curtain walling - air permeability - test method |
| BS EN 12154 | Curtain walling. Water tightness. Performance requirements and classification |
| BS EN 12155 | Curtain walling – water tightness - laboratory test under static pressure |
| BS EN 12179 | Curtain walling - resistance to wind load - test method |
| BS EN 12600 | Glass in building - pendulum test - impact test method and classification for flat glass |
| BS EN 13050 | Curtain Walling. Water tightness. Laboratory test under dynamic condition of air pressure and water spray |
| BS EN 356 | Glass in building - security glazing - testing and classification of resistance against manual attack |
| CAN/CGSB 41.24-95 | Rigid vinyl siding, soffits and fascia |
| CAN/CGSB 82.1 | Sliding doors |
| CAN/CGSB-12.1 | Tempered or laminated safety glass |
| CAN/CSA O325.1 | Test methods for construction sheathing |
| CAN/ULC-S102 | Standard method of test for surface burning characteristics of building materials and assemblies |
| CAN/ULC-S704 | Standard for thermal insulation, polyurethane and polyisocyanurate, boards, faced |
| CAN/ULC-S770 | Standard test method for determination of long-term thermal resistance of closed-cell thermal insulating foams |
| CPSC 16 CFR Part 1201 | Safety Standard for Architectural Glazing Materials |
| CSA A123.21 | Standard test method for the dynamic wind uplift resistance of membrane-roofing systems |
| CSA A440 | Windows |
| CSA A440.2/A440.3 | Fenestration energy performance / user guide to CSA A440.2-14 |
| CSA O437.1 | Test methods for waferboard and strandboard |
| FM 4470 | Single-ply, polymer-modified bitumen sheet, built-up roof (BUR) and liquid applied roof assemblies for use in class 1 and noncombustible roof deck construction |
| FM 4473 | Specification test standard for impact resistance testing of rigid roofing materials by impacting with freezer ice balls |
| FM 4474 | Standard for evaluating the simulated wind uplift resistance of roof assemblies using static positive and/or negative differential pressures |
| GSA-TS01-2003 | Standard test method for glazing and window systems subject to dynamic overpressure loadings |
| ICC ES AC04 | Sandwich panels |
| ICC ES AC05 | Sandwich panel adhesives) |
| ICC ES AC07 | Special roofing systems |
| ICC ES AC109 | Thermoplastic composite lumber products |
| ICC ES AC11 | Cementitious exterior wall coatings |
| ICC ES AC13 | Joist hangers and similar devices |
| ICC ES AC132 | Attic Vents |
| ICC ES AC148 | Flexible flashing materials- for use with the 2015, 2012 and 2009 I-codes |
| ICC ES AC15 | Concrete floor, roof and wall systems and concrete masonry wall systems |
| ICC ES AC16 | Plastic glazed skylights |
| ICC ES AC166 | Metal roof coverings |
| ICC ES AC174 | Deck board span ratings and guardrail systems (guards and handrails |
| ICC ES AC177 | Translucent fiberglass reinforced plastic (FRP) faced panel wall, roof and skylight systems |
| ICC ES AC188 | Roof underlayments |
| ICC ES AC212 | Water-resistive coatings used as water-resistive barriers over exterior sheathin |
| ICC ES AC227 | Rigid cellular PVC non load-bearing exterior trim |
| ICC ES AC233 | Alternate Dowel-type Threaded Fasteners |
| ICC ES AC235 | EIFS clad drainage wall assemblies |
| ICC ES AC245 | Windows and doors subject to wind-borne debris |
| ICC ES AC25 | Metal composite material (MCM) |
| ICC ES AC257 | Corrosion-resistant Fasteners and Evaluation of Corrosion Effects of Wood Treatment |
| ICC ES AC265 | Fiber-reinforced polymer (FRP) composite columns used as axial load-bearing and non load-bearing architectural and decorative columns |
| ICC ES AC269 | Racking shear evaluation of proprietary sheathing materials attached to light-frame wall construction or code-complying sheathing attached to light-framed walls with proprietary fasteners |
| ICC ES AC273 | Handrails and guards |
| ICC ES AC295 | Laminated fibrous board sheathing material |
| ICC ES AC310 | Water-resistive membranes factory-bonded to wood-based structural sheathing, used as water-resistive barriers |
| ICC ES AC364 | Mechanically operated flood vents |
| ICC ES AC365 | Building integrated photovoltaic roof modules |
| ICC ES AC368 | Suspended ceiling framing systems |
| ICC ES AC38 | Water-resistive barriers |
| ICC ES AC380 | Termite physical barrier systems |
| ICC ES AC382 | Laminated fibrous board sheathing material used as a water-resistive barrier |
| ICC ES AC386 | Acceptance Criteria for Fiber-reinforced Magnesium-oxide-based Sheets |
| ICC ES AC39 | Walking decks |
| ICC ES AC439 | Glass railing and balustrade system |
| ICC ES AC447 | Fiber reinforced plastic (FRP) modular wall systems |
| ICC ES AC452 | Rigid cellular polystyrene (RCPS) geofoam used in interior floor applications |
| ICC ES AC46 | Cold-formed steel framing members |
| ICC ES AC49 | Molded plastic footing pads |
| ICC ES AC51 | Precast stone veneer |
| ICC ES AC71 | Foam plastic sheathing panels used as weather-resistive barriers |
| ICC ES AC75 | Membrane roof-covering systems |
| ICC ES AC81 | Cotton fiber insulation |
| ICC ES AC86 | Cold-formed steel framing members-interior non load-bearing wall assemblies |
| ICC ES AC90 | Fiber cement siding used as exterior wall siding |
| ICC-ES AC66 | Acceptance Criteria for Fire Retardant Wood |
| ISO 10140-2 | Acoustics - Laboratory measurement of sound insulation of building elements - Part 2: Measurement of airborne sound insulation |
| ISO 10140-3 | Acoustics - Laboratory measurement of sound insulation of building elements - Part 3: Measurement of impact sound insulation |
| ISO 10140-5 | Acoustics - Laboratory measurement of sound insulation of building elements - Part 5: Requirements for test facilities and equipment |
| ISO 140-18 | Acoustics - Measurement of sound insulation in buildings and of building elements -- part 18: laboratory measurement of sound generated by rainfall on building elements |
| ISO 15665 | Acoustics - Acoustic insulation for pipes, valves and flanges |
| ISO 354 | Acoustics - Measurement of sound absorption in a reverberation room |
| ISO 3741 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure -- precision methods for reverberation test rooms |
| ISO 717-1 | Acoustics - Rating of sound insulation in buildings and of building elements - Part 1: Airborne sound insulation |
| ISO 717-2 | Acoustics - Rating of sound insulation in buildings and of building elements - Part 2: Impact sound insulation |
| NFPA 251 | Standard methods of tests of fire resistance of building construction and materials |
| NFPA 252 | Standard methods of fire tests of door assemblies |
| NFPA 255 | Standard method of test of surface burning characteristics of building materials |
| NFPA 256 | Standard methods of fire tests of roof coverings |
| NFPA 257 | Standard on fire test for window and glass block assemblies |
| NFPA 265 | Standard methods of fire tests for evaluating room fire growth contribution of textile or expanded vinyl wall coverings on full height panels and walls |
| NFPA 268 | Standard Test Method for Determining Ignitability of Exterior Wall Assemblies using Radian Heat Energy source. |
| NFPA 275 | Standard method of fire tests for the evaluation of thermal barriers |
| NFPA 285 | Standard fire test method for evaluation of fire propagation characteristics of exterior non-load-bearing wall assemblies containing combustible components |
| NFPA 286 | Standard methods of fire tests for evaluating contribution of wall and ceiling interior finish to room fire growth |
| NFPA 701 | Standard methods of fire tests for flame propagation of textiles and films |
| NFRC 100 | NFRC procedures for U-factor |
| NFRC 100 | Procedure for determining fenestration product u-factors |
| NFRC 101 | Procedure for determining thermos-physical properties of materials for use in NFRC-approved software |
| NFRC 102 | Procedure for measuring the steady-state thermal transmittance of fenestration systems |
| NFRC 200 | Solar heat gain coefficient |
| NFRC 200 | Determining fenestration product solar heat gain coefficient and visible transmittance at normal incidence |
| NFRC 400 | Procedure for determining fenestration product air leakage |
| NFRC 500 | Procedure for determining fenestration product condensation resistance values |
| NIJ 0108.01 | Ballistic Resistant Protective Materials |
| NRC-CNRC CCMC TG 06522 | Technical guide for wood thermoplastic composite lumber exterior decking (solid cross section) |
| NRC-CNRC CCMC TG 06525 | Technical guide for cellulosic/polymer composite exterior decking (hollow cross-section) |
| RILEM TC 127-MS.B.5 | Tests for masonry materials and structures – determination of the damage to wallettes caused by acid rain |
| SFM 12-7A-1 | Materials and construction methods for exterior wildfire exposure – exterior wall siding and sheathing |
| SFM 12-7A-2 | Materials and construction methods for exterior wildfire exposure - exterior windows |
| SFM 12-7A-3 | Materials and construction methods for exterior wildfire exposure - horizontal projection underside |
| SFM 12-7A-4 | Materials and construction methods for exterior wildfire exposure - decking |
| SFM 12-7A-4A | Materials and construction methods for exterior wildfire exposure - decking alternate method A |
| TAS 100 | Test procedure for wind and wind driven rain resistance of discontinuous roof systems |
| TAS 100A | Test procedure for wind and wind driven rain resistance and/or increased windspeed resistance of soffit ventilation strip and continuous or intermittent ventilation system installed at the ridge area |
| TAS 103 | Test procedure for self-adhered underlayments for use in discontinuous roof system |
| TAS 112 | Standard requirements for concrete roof tiles |
| TAS 201 | Impact test procedures |
| TAS 202 | Criteria for testing impact and non-impact resistant building envelope components using uniform static air pressure |
| TAS 203 | Criteria for testing products subject to cyclic wind pressure loading |
| UBC Standard 24-2 | Safety glazing |
| UFC 4-010-01 | DoD minimum antiterrorism standards for buildings |
| UL 10B | Standard for fire tests of door assemblies |
| UL 10C | Standard for positive pressure fire tests of door assemblies |
| UL 1715 | Standard for fire test of interior finish material |
| UL 1897 | Standard for uplift tests for roof covering systems |
| UL 1975 | Standard for fire tests for foamed plastics used for decorative purposes |
| UL 2218 | Standard for impact resistance of prepared roof covering materials |
| UL 263 | Standard for fire tests of building construction and materials |
| UL 580 | Standard for tests for uplift resistance of roof assemblies |
| UL 608 | Standard for emergency vault ventilators and vault-ventilating ports |
| UL 723 | Standard for test for surface burning characteristics of building materials |
| UL 746C | Standard for polymeric materials - use in electrical equipment evaluations |
| UL 752 | Standard for bullet-resisting equipment |
| UL 790 | Standard for standard test methods for fire tests of roof coverings |
| UL 9 | Standard for fire tests of window assemblies |
Let us know more about your requirement, contact us.